重型摩托車
Heavy motorcycle
第一課時 – 車頭
Lesson 1 – Vehicle Head
一、活動目標
I. Objectives
1．了解重型摩托車的結構組成。
Understand the structural composition of heavy-duty motorcycles.
2．學會用對稱夾擊的方法拼裝車頭。
Learn to assemble the head by means of symmetrical pinch.
二、欣賞
II. Appreciation
（出示重型摩托車結構組成圖片）
(Show pictures of structural composition of heavy motorcycle)
重型機車是一般指發動機排量在400cc以上的摩托車。機車是臺灣的說法，香港稱為電單車，中國大陸地區稱為摩托車，但是為了與普通摩托區分，大陸地區也稱它為機車。
Heavy motorcycles generally refer to motorcycles with engine displacement above 400 cc. Motorcycle is the saying in Taiwan, in Hong Kong it is called motorbike, and in Mainland China it is called engine-powered motorcycle in order to distinguish it from ordinary motorcycle.
三、分析
III. Analysis
圖一：用夾心法，把黑色厚墊片固定在兩個零件之間，要求孔的位置和方向一致，并緊固。
Figure 1: Use the sandwich method to secure the black thick gasket between the two parts, requiring the holes in the same position and orientation, then tightened.
圖二：兩邊對稱，上下對稱，并夾擊紅色的鐵片在鐵片與黑色厚墊片之間。這里對零件的順序要求比較高。注意兩邊零件的位置一定要你相互對稱。不可出現一個在內，一個在外的交錯現象。
Figure 2: The two sides are symmetrical to each other, and do the same to the top and bottom; the red iron sheet is sandwiched between the iron sheet and the black thick gasket. Here, the requirement to the installing sequence of the parts is relatively higher. Pay attention to the position of the parts on both sides and make sure that they are symmetrical with each other. There must be no intertwining with one inside and one outside.
四、認知與管理
IV. Cognition and Management
1．認識黑色厚硬墊片，區分6號螺絲和10號螺絲。
Learning black thick hard gasket, distinguish 6mm screws and 10mm screws.
2．管理自己的工具箱，拿出工具、操作盤和重型摩托車1號袋零件。
Manage your own toolbox; take out tools, operating board and heavy-duty motorcycle parts in the bag No. 1.
3．檢查零件種類與數量。
Check the type and quantity of parts.
五、拼裝
V. Assembling
結合3D動畫進行模塊1的拼裝與建構。
Module 1 is assembled and constructed with 3D animation.
重型摩托車
Heavy Motorcycle
第二課時 – 車把與車燈
Lesson 2 – Handlebar and Lamps
一、活動目標
I. Objectives
1．了解重型摩托車的特點，并感受重型摩托車“重”的力量。
Understand the features of heavy motorcycle and feel the “heavy weight” of heavy motorcycle.
2．技巧連接車燈與車把，銜接好上下結構的關系。
Connect the lamp and handlebar by skills, combining the upper and lower structure of the parts.
二、欣賞
II. Appreciation
（欣賞重型摩托車一段開跑視頻）
(Enjoy the video of a running heavy-duty motorcycle)
它由汽油機驅動，靠手把操縱前輪轉向的兩輪或三輪車，輕便靈活，行駛迅速，廣泛用于巡邏、客貨運輸?shù)?，也用作體育運動器械。
Powered by a gasoline engine, the motocycle with two wheels or three wheels, which steer the front wheel by handbar, is light, flexible, fast, widely used in patrol, passenger and cargo transportation and etc., this motocycles are also used as sports equipment.
三、分析
III. Analysis
圖一、二、三：單個拼裝車燈，車把，以及連接部分。
Figures 1, 2 and 3: Assembling lamp, handlebar, and connecting parts one by one.
圖三：車把的前后方向要保持一致。
Figure 3: The front and rear direction of the handlebar should be consistent.
圖四、五：再用最長的30MM的螺絲連接1車把，2車燈，3車頭上下孔，其中間要穿進一個連接模塊。保證6孔合一的同時，要注意車燈和車把的方向應該是相反的。
Figure 4 and 5: Connect upper and lower holes of handlebar 1, lamps 2 and head 3 with the longest 30mm screw, a connecting module shall be inserted between them. Ensure that the 6 holes are well aimed while noting that the direction of the lamp and handlebar should be opposite.
四、認知與管理
IV. Cognition and Management
1．認識橋型3孔和5孔鐵片，區分黑色燈罩與其他黑色鐵片。
Learning bridge shaped 3-hole and 5-hole iron sheet, distinguish black lampshade from other black iron sheets.
2．管理自己的工具箱，拿出工具，操作盤和重型摩托車2號袋零件。
Manage your own toolbox, take out tools, operating board and heavy duty motorcycle parts in the bag No. 2.
3．檢查零件種類與數量。
Check the type and quantity of parts.
五、拼裝
V. Assembling
結合3D動畫進行模塊2的拼裝與建構。
Module 2 is assembled and constructed with 3D animation.
重型摩托車
Heavy Motorcycle
第三課時 – 發動機
Lesson 3 – Engine
一、活動目標
I. Objectives
1．了解重型摩托車的發動機原理并感受發動機的魅力。
Learning the engine principle of heavy motorcycle and feel the charm of engine.
2．學會疊加法拼裝復雜型發動機。
Learn to set up a complex engine by stacking method.
二、欣賞
II. Appreciation
（聽一段重型摩托車發動機的聲效）
Listening to the sound effect of a heavy motorcycle engine.
重型摩托車為什么稱之為重型，主要就是因?yàn)樗陌l(fā)動機。重機是摩托里的一種,摩托車48CC以下是助力車,48CC-600CC之間的摩托只能稱作是普通摩托車,600CC以上都稱重機,也叫重型機車．但1000CC以上的都稱之為公升級重機摩托了。
The reason why a heavy motorcycle is called heavy is mainly because of its engine. Heavy engine motorcycle is one of the motorcycles. The motorcycles below 48CC are mopeds. The motorcycles between 48CC and 600cc can only be called ordinary motorcycles. The motorcycles above 600cc are all called heavy motorcycles. But the motorcycles above 1000cc are called Litre Level heavy engine motorcycles.
三、分析
III. Analysis
圖一、二：零件與零件之間的上下方位關系要調整好，單個獨立拼裝好放置旁邊作為備用。
Figs. 1 and 2: The upper-and-lower orientation relationship between parts shall be adjusted, and single independent assembled combination shall be set aside for standby.
圖三：疊加法拼裝出一個復雜的發動機部分，第一層和第二層用的是3孔鉆石型鐵片左右對稱疊加。其長螺絲應該在4個孔并排的一邊，短一點的螺絲在另外一邊。這里一定不能交換位置。
Figure 3: The stacking method creates a complex engine. The first and second layers are constructed by left-right symmetrical stacking with 3-hole diamond-shaped iron sheets. The long screw should be at the same side with 4 holes side by side, the shorter screw on the other side. There must be no exchange of positions at here.
圖四、五：把1．2．3組合在一起，注意發動機和圖二的上下關系，更注意發動機里的長短螺絲的前后關系。
Figs 4, 5: Combining 1.2.3, pay attention to the upper and lower relationship between the engine and Figure 2, and pay more attention to the front and back relationship between the long and short screws in the engine
四、認知與管理
IV. Cognition and Management
1．認識3孔鉆石型鐵片與6孔正方形鐵片之間的關系。
Understanding the relationship between 3-hole diamond iron sheet and 6-hole square iron sheet.
2．管理自己的工具箱，拿出工具，操作盤和重型摩托車3號袋零件。
Manage your own toolbox; take out tools, operating board and heavy-duty motorcycle parts in the bag No. 3.
3．檢查零件種類與數量。
Check the type and quantity of parts.
五、拼裝
V. Assembling
結合3D動畫進行模塊3的拼裝與建構。
Module 3 is assembled and constructed with 3D animation.
重型摩托車
Heavy Motorcycle
第四課時– 車身，座椅，引擎蓋
Lesson 4 – Body, Seat, Engine Hood
一、活動目標
I. Objectives
1．感受重型摩托車的速度力量。
Feel the speed and power of heavy motorcycle.
2．對稱組合車身與車座，掌握用螺絲固定螺母的同時組裝法。
Symmetrically combine the vehicle body and the seat, mastering simultaneous assembly method for fixing nuts with screws.
二、欣賞
II. Appreciation
（欣賞一段重型摩托車與跑車比賽視頻）直觀感受重型摩托車的速度力量以及越野能力。
(Enjoy a video of heavy motorcycle and sports car competition) intuitively feel the speed strength and cross-country ability of heavy motorcycle.
三、分析
III. Analysis
圖一：7孔V型鐵片作為車身固定在發動機車架的上方，要求螺母先對準放好，再兩個螺絲同時拼裝固定。這里鐵片在外，黑色圓柱形鐵片在中間的里外位置不要錯。以及V型的上下位置不要錯。
Fig 1: The 7-hole V-shaped iron sheet is fixed on the top of the engine frame as the body, and the nut is required to be aligned and placed first, and then two screws are assembled and fixed at the same time. Here the iron sheet keeps outside, the black cylindrical iron sheet keeps inside, the inner and outer position should not be wrong. And the upper and lower position of the V-shape part must be correct.
圖二：發動機蓋的前后位置，以及孔的位置不要弄錯。左右兩邊的2孔L型在固定前一定要向外拉到最長。
Fig 2: Do not mistake the front and rear positions of the engine hood and the holes. The 2-hole L-shaped parts on the left and right must be pulled outward to the longest distance before fixed.
圖三：座椅重疊組合固定在車身的上方，孔的位置上下對齊。
Fig. 3: The seat assembly is fixed on the upper side of the vehicle body by overlapping, and the upper and lower positions of the holes are aligned.
圖四：最后調整好每個螺絲與螺母之間的關系，保證不松動。
Figure 4: Finally, adjust the relationship between each screw and nut to ensure that they do not get loose.
四、認知與管理
IV. Cognition and Management
1．認識7孔V型鐵片，區分兩種2孔L型鐵片。
Recognize 7-hole V-shaped iron sheet, distinguishing two kinds of 2-hole L-shaped iron sheet from each other.
2．管理好工具箱，拿出工具，操作盤和重型摩托車4號袋零件。
Manage your own toolbox; take out tools, operating board and heavy-duty motorcycle parts in the bag No. 4.
3．檢查零件種類與數量。
Check the type and quantity of parts.
五、拼裝
V. Assembling
結合3D動畫進行模塊4的拼裝與建構。
Module 4 is assembled and constructed with 3D animation.
重型摩托車
Heavy Motorcycle
第五課時 – 底盤拼裝
Lesson 5 – Chassis Assembly
一、活動目標
I. Objectives
1．了解駕駛重型摩托車所需證件。
Learning the licenses required for driving heavy motorcycles.
2．對稱組合底盤的里外前后，掌握螺母在中間位置的固定法。
Symmetrically combining the inside and outside of the chassis, master the fixing method of the nut in the middle position.
二、欣賞
II. Appreciation
摩托車的駕照有F、E和D三種，其中F證只能駕駛發動機排量在50CC以下（不含50CC）的兩輪輕便摩托車，E證可以駕駛所有的兩輪摩托車，不管多大排量的都可以，它的準駕車型包括F證，D證可以駕駛包括三輪和兩輪在內的摩托車，也是所有排量的都可以，它的準駕車型包括F證和E證。重型摩托車，應該是指大排量的摩托車，這種摩托車用E證或D證都可以駕駛。有證才可以駕駛哦！
There are three types of driving licenses for motorcycles: F, E and D. F license can only drive two wheels mopeds with engine displacement less than 50cc (excluding 50cc), E license can drive all two wheeled motorcycles, no matter how much the displacement is, E license is qualified to all displacement specified in F license, D license can drive motorcycles including three wheels and two wheels with all displacement, D license is qualified to all displacement specified in E, F license. Heavy-duty motorcycle, which should be a large-displacement motorcycle, can be driven with both E and D licenses. You can‘t drive without a driving license!
三、分析
III. Analysis
圖一：底盤中心軸，上下關系注意并擰緊每一個螺絲與螺母。
Figure 1: Pay attention to the upper and lower relationship of center axis of chassis, and tighten each screw and nut.
圖二： 5個零件組合成底盤的一側，7孔V型鐵片要注意長短頭的方向。鉆石型鐵片要注意上下的位置。以及所有零件的先后順序。
Figure 2: 5 parts combined into one side of the chassis, we should pay attention to the direction of long and short end of 7-hole V-shaped iron sheet. Pay attention to the up and down position of the diamond-shaped iron sheet and the installing sequence of all the parts.
圖三：在圖二的基礎上，兩邊對稱組合出整個底盤部分。這里特別注意固定V型鐵片的第二個螺母是在兩個零件的中間，這里可以借助扳手一起幫忙固定。
Fig. 3: On the basis of Fig. 2, the entire chassis is assembled by symmetrically combining both sides. It is particularly noted here that the second nut for securing the V-shaped iron sheet is in the middle of the two parts; it can be secured with a wrench.
四、認知與管理
IV. Cognition and Management
1．認識7孔V型鐵片，兩孔直型的特殊性鐵片，并了解用途。
Learning the special features of 7-holes V-shaped iron sheet and 2-holes straight-shaped iron sheet, understand the applications of them.
2．管理好工具箱，拿出工具，操作盤，和哈雷摩托車5號袋零件。
Manage your own toolbox; take out tools, operating board and heavy-duty motorcycle parts in the bag No. 5.
3．檢查零件種類與數量。
Check the type and quantity of parts.
五、拼裝
V. Assembling
結合3D動畫進行模塊5的拼裝與建構。
Module 5 is assembled and constructed with 3D animation.
重型摩托車
Heavy Motorcycle
第六課時 – 底盤，車身與車頭的整體組合
Lesson 6 – Overall Combination of Chassis, Body and Head
一、活動目標
I. Objectives
1．了解駕駛摩托車的必備裝備。
Understand the necessary equipment for driving motorcycle.
2．連接組合車身與車頭，底盤，巧妙安裝好引擎的左右擋板。
Combining body, head and chassis, and skillfully install the left and right baffle plates of the engine.
二、欣賞
II. Appreciation
（看圖片）騎摩托車，一套齊全的裝備可以保證駕駛員的安全。應付各種惡劣的氣候環境或者各種突發的危機：例如壞車、事故。1．頭盔2．軀干防護用品3．應急修車工具4．風擋5、保暖裝備
(Seeing picture) Riding a motorcycle, a complete set of equipment can ensure the safety of the driver. Deal with all kinds of bad weather or sudden event: such as motorcycle failure, accident, etc. No.1 Helmet No.2 Torso protection products No.3 Emergency repair tools No.4 Windshield No.5 Thermal equipment
三、分析
III. Analysis
圖一：組合車輪。內輪胎與外輪胎漢堡法夾擊，注意內部的大小孔相對而合。再固定外輪轂。
Figure 1: Wheel Combination. The inner tire and the outer tire are combined with the hamburger method. Pay attention to the large and small inner hole attached against each other, then fixing outer wheel hub.
圖二：用一根5孔直型鐵片連接底盤，中間的黑色墊片至關重要。
Figure 2: Use a 5-holes straight iron sheet to connect the chassis, the black gasket in the middle is very important.
圖三、四：再在5孔鐵片的另外一頭固定車頭和車身，其黑色墊片在中間。與底盤上下一致。這里的2個螺絲螺母要求固定穩固。
Figure 3 and 4: Fix the head and body by the other end of the 5-hole iron sheet with the black gasket in the middle. Keep well aligned with the upper and lower of chassis. The 2 screw and nut here are required to be fixed firmly.
四、認知與管理
IV. Cognition and Management
1．認識輪轂，外輪胎，內輪胎，并區分關系。
Recognize hub, outer tire, inner tire, and distinguish the relationship.
2．管理好工具箱，拿出工具，操作盤，和重型摩托車6號袋零件。
Manage your own toolbox; take out tools, operating board and heavy-duty motorcycle parts in the bag No. 6.
3．檢查零件種類與數量。
Check the type and quantity of parts.
五、拼裝
V. Assembling
結合3D動畫進行模塊6的拼裝與建構。
Module 6 is assembled and constructed with 3D animation.
重型摩托車
Heavy Motorcycle
第七課時– 安裝前后輪和左右引擎蓋
Lesson 7 – Installing the Front and Rear Wheels and the Left and Right Hoods
一、活動目標
I. Objectives
1．嘗試駕駛摩托車，了解駕駛摩托車的操作方法。
Try to drive a motorcycle and learn how to operate it.
2．慢穿法安裝車輪，隱藏法安裝左右引擎蓋。
Install the wheels by slow-through method, and install the left and right hoods by hiding method.
二、欣賞Appreciate
II. Appreciation
模擬駕駛：手抓緊離合打火，然后掛1檔，慢松離合加油門，就走了，剎車的時候最好要換到空擋上再剎車，這樣不滅火，實在是緊急情況空擋來不及退就捏緊離合剎車。
Driving Simulation: Hold the clutch to start the fire, and then shift to gear 1, slowly release the clutch fuel valve, and then walk away. When braking, it’s better to shift to the neutral gear and brake again, so as not to put out the fire. Grasp the clutch brake tightly in emergency if it is to late to shift gear to neutral position.
三、分析
III. Analysis
圖一：安裝引擎的左右擋板，螺母在整個車身的里面，這里建議在固定前，把擋板往上放，固定緊后再把擋板放下來，借助扳手固定緊。
Figure 1: Install the left and right baffles of the engine; the nuts are in the whole body. It is recommended to put the baffles up before fixing, and then put the baffles down after fixing; a wrench is helpful for fixing here.
圖二：用長螺絲巧妙穿進左右兩邊的零件并擰緊。特別注意后輪的6孔V型和7孔V型的里外位置要一致。
Figure 2: Insert the left and right parts with long screws, and tighten them. Pay special attention to the inner and outer positions of the 6-holes V-shape and 7-hole V-shape of the rear wheel.
四、認知與管理
IV. Cognition and Management
1．認識前輪后輪固定的位置，和里外間的關系。
Knowing the fixed position of front wheel and rear wheel, and the relationship between inside and outside.
2．管理好工具箱，拿出工具，操作盤，和重型摩托車7號袋零件。
Manage your own toolbox; take out tools, operating board and heavy-duty motorcycle parts in the bag No. 7.
3．檢查零件種類與數量。
Check the type and quantity of parts.
五、拼裝
V. Assembling
結合3D動畫進行模塊7的拼裝與建構。
Module 7 is assembled and constructed with 3D animation.
迪朗上海翻譯公司負責翻譯并校對
